- 0.2 mm.sq. The outer diameter of the PVC insulated wire is about 1.0 mm. Then we get the outer diameter of the disk 200-250 mm. If we get 500 kHz and above, we need to wind a certain number of turns to lower the natural frequency.
- 20 m of 4-core telephone cable SHTLP-4 (remove the braid), you get a disk with a diameter of 21 cm with a frequency of 300-310 kHz.
- MGTF wire, 25 25 meters with an outer diameter of 0.9 mm. The disk turned out to be 210 mm in diameter. 278 kHz.
- wire in varnish with a diameter of 0.5 mm, winding a disk with a diameter of 11 cm = 350 kHz, if the diameter is 11.6 cm = 283 kHz. If you fill it with PVA glue, the frequency may drop by 30 kHz.
The base can be made from fiberboard or an old plate, onto which double tape is glued. Plexiglas can also be used for the base, but it screens external small turbulences, but not controllable ones. We make a hole in the center, where we insert a double wire, one of which we will supply power to (they must be the same length). And we begin to wind the double spiral from the center clockwise (Fig. 1), gluing the wires to double tape. Do not use epoxy resin for fastening, which, being a crystalline substance, introduces peculiarities into the operation of the capacitive coil! At the end, you can drill holes under the wires, insert them and secure them with glue so that the coil holds better. To further strengthen it, you can wrap it with wide tape or fill it with PVA.
Therapeutic torus (TMA) is designed to treat local problem areas.
To make a TMA, you need a corrugation, which is cut lengthwise and rolled into a torus so that the outer cut side is on the outside (see figure). The diameter of the internal hole of the torus should ideally be 1 inch (~25 mm), but options with a slightly larger diameter are also possible, then the torus will have a slightly weaker effect, but it may turn out to be at a different frequency, which is also useful in treatment. The inner hole of the donut affects the intensity of the impact. The smaller the diameter of the hole, the stronger the impact, but this is a strong load on the body’s excretory systems. The internal diameter should not be less than 25 mm.
We take the wire UTP (this is a twisted pair cable for connecting to the Internet). From this wire we take out one twisted pair (double twisted wire) ~18 meters long and throw our torus. As a result, we get a kind of inductance capacitor, the capacitance of which is the interturn (interwire) capacitance created by the insulation of the twisted pair wires and the gap between them. Apply power to the beginning of one wire and to the end of the other, and leave the rest in the air (diagram in the figure).
- UTP wire - twisted pair from a computer cable. Length? m. We take the corrugation for winding with a length of approximately? cm. We roll it into a torus, the internal diameter is 2.5 cm. The operating frequency will be approximately? kHz.
- UTP wire - twisted pair from a computer cable. Length 16.5 m. We take a corrugation for winding approximately 19 cm long. We roll it into a torus, the inner diameter is 3 cm, the outer diameter is 6 cm. The operating frequency is approximately 280 kHz. If you wrap it with electrical tape, it reduces the operating frequency by ~6 kHz
- UTP wire - twisted pair from a computer cable. Length 18 m. Inner diameter – 4 cm. Corrugation for winding approximately 23 cm long.
Electrical appliance generating a high frequency sinusoidal signalTGS-3A is designed to power a capacitive or inductive load with a power of no more than three watts. Power is supplied from a single-phase network with a voltage of 220V 50Hz, or from a 12V backup power source (for example, a car battery). The actual generation frequency range is around 300 kHz. The device is equipped with a power switching button 100% - 50%. It is advisable to start exposure at reduced power. There is a field rotation switch. This mode must be turned on alternately with the normal mode.
Working with the device Mishina coil . You can order coils and generator -
This model Mishina coils TGS-3A is manufactured directly under the direction of Alexander Mishin himself and is equipped with automatic resonance adjustment for a coil or torus and does not require human intervention, except in cases of limiting the power of the device (100% -50%). When connecting the connector from the coil to the generator, pay attention to the grooves in the connectors; they must match. Insert the generator plug into the network and move the switch on the generator housing (on the left side) to the ON (I) position. The device can be seen to be turned on by a flashing indicator in the center of the front panel. On the right side of the housing, the power switch (100%-50%) can be installed in the position you need. Then select the timer time mode and click on the corresponding button. There are four time ranges available for the timer: 15 minutes, 30 minutes, 60 minutes and infinity. In this case, the power indicator will switch to a constant glow mode, and under the timer mode button, a flashing indicator of the selected mode signals that the generator is turned on. When the indicator on the instrument panel \\\\\\\"no resonance\\\\\\\" goes out, this will mean that the coil or torus installed in the device is configured and ready for use.
Do not forget to check the operation of the capacitive coil after connecting it to the device. Job Mishina coils with generator TGS-3A- can be checked at any time by holding the field indicator close to it, and the LED will change the brightness of the glow depending on the distance to the coil. After the selected mode has expired, the generator will turn off automatically. This is indicated by a flashing central indicator, and the indicator under the timer button will go out. Be careful, the generator will not turn off in infinity mode and will need to be turned off manually!
FREQUENCIES
Recommended by A.N. Mishin frequency: about 300 kHz (this is how the coils of the Tolyatinsk plant are configured)
VOLTAGE, CURRENT, SIGNAL FORM
Sinusoidal signal (however, some manufacturers use a meander at their own peril and risk, which Mishin does not recommend)
PRECAUTIONS
A.N. Mishin advises always starting the treatment with a large coil, placing it on the back, on the kidneys; many people have them clogged. Be careful with older people - start little by little with 10 minutes a day.
DURATION OF EXPOSURE
For the elderly, start carefully with 10-20 minutes a day (since the coil can “pick up a lot of sores at once” and the kidneys will have a large load on removing toxins, and the pressure may jump).
Average duration of exposure to a large coil: 30 minutes per session (1-2 sessions per day). With a small torus locally for a specific area - 10-15 minutes.
Recommendation by A.N. Mishina: no more than 1 hour per day (2 hours maximum per day).
For the elderly, 15-30 minutes 2 times a day - every other day.
The speed of onset of the effect and the total duration of exposure are individual (from 1 session to several weeks and even months). At long-term use you need breaks of 1-2 weeks. This is important for regeneration!
After completing the course for 2-4 weeks, if there are no side effects, you can connect a pure static coil and dual-frequency. These coils have a stronger field and do not need to be placed on the body. You can put it nearby.
SIDE EFFECTS
Excessive PRESSURE can be removed with a torus on the kidneys (5-15 minutes for each).
It is normal when the kidneys begin to hurt due to exposure - this is the result of the removal of salts, toxins, etc., as soon as the urine darkens and acquires an unpleasant odor (usually on the 4th-5th day), you need to take a break, stop working for a while until these symptoms disappear .
If the pressure jumps sharply, then we take a break for tea with lemon; as soon as the pressure is restored, we take up the coil again.
The HEART may ache noticeably - this is normal, the infection is coming out.
Various Pimples and the like on the skin are normal, the disease goes away. This means that the kidneys cannot cope and the body “expels” the nasty stuff through the skin. In this case, it is recommended to work only on the kidneys with coils, for 10-15 minutes and with low voltage.
WHAT TO INFLUENCE
The torus is more suitable for liquefying compactions, and the flat one helps the body with regeneration and a strong increase in immunity. So far, this is exactly the effect observed in the majority of cases.
A large coil has a softer and more extensive effect on the entire body, while a torus (or small donut) works more focused on specific areas.
LOCATION OF EXPOSURE
First, a general impact with a large coil on the chest and kidneys is recommended, then a targeted torus (or a very small donut made of thin wire) on the problem area.
The torus has additional harmonics for radiation, so you need to be more careful with it on your head. Monitor your health.
DISTANCE
For those who work with others, you need to be 3 m further from the patient to avoid an overdose.
INTERFERENCE
Springs in the mattress, titanium dental implants do not have much effect, but it is better to remove chains, rings and earrings. It is better to remove everything metal from the affected area (belt buckle, metal fasteners, buttons, etc.).
It would be preferable not to be nearby cell phones, Wi-Fi and other “emitters”.
Working with PURE STATIC coil and dual frequency coil
These are new, more powerful coils. A pure static coil has no electromagnetic component and affects structures in the body that are not amenable to capacitive coils. They have a stronger and larger field up to several meters. They work throughout the body, not locally. You don’t even have to apply it anywhere. Just put it next to it.
Start no more than 10 minutes. Listen carefully to the body. In case of exacerbation of diseases, take a break until the condition normalizes.
Gradually add 5 minutes of work time. You can start working with these coils only after you have completed a course of treatment on the main coils in three to four weeks.Important.
Avoid overdose. Overdose may cause cardiac arrhythmia. If this happens, you need to stop exposure until the situation normalizes.
The scheme of influence on all problems is approximately the same - start with small doses with a large coil of the main set - (kidneys-solar plexus). Then the torus - locally by zone. Gradually increase the exposure time to 1 hour per session. Then move on to more powerful reels.
Attention!
If you do not follow the recommendations for use and immediately start working with large doses, you may experience an increase in temperature to 39 degrees or higher, vomiting, and weakness. These symptoms may appear several hours after overdose exposure.
Blood diseases. In particular Lymphocytic leukemia. Yes, everything is fine, I should use a flat coil to break up the mutants. start the standard 30-60 minutes a day, 5-7 days in a row, monitor the sensations in the kidneys and the color of urine. Apply flat alternately to chest/back. she studies her whole body in search of sores) Drug addiction If anyone has used drugs, it relieves toxic addiction, but you can catch a visit after the procedure
The optimal ratio of internal diameter to external diameter is 1/3
- Large flat coil - internal D - 70-80 mm, external - 240 mm, SHTLP-4 wire two cores.
- Flat coil 120-130 mm. internal D - 40mm, external - 120 mm, wire 0.5mm varnish. Optimal operating frequencies are 270-330 kHz.
How to make a Mishin coil with your own hands
- 1. We start making a flat Mishin coil from the base. We make a base onto which we glue double-sided tape.
- 2. In the center of the base we install a round protrusion with a diameter of approximately 40 mm.
- 3. Take a varnished wire 0.5 mm in diameter and 10-12 meters long.
- 4. Around the round protrusion you need to wind two wires at once parallel to the plane of the base.
- 5. After manufacturing the coil, it is necessary to determine the frequency of operation of this container:
Scheme for manufacturing a flat coil. D - 120-130 mm.
We make two taps from the coil. We take the end of one wire from the inside of the coil and the second from the other wire from the outside. In this case, the circuit remains open, and the two unused outputs of the plates are simply cut off.
Option 2The flat coil works on minor problems such as viruses and fungal diseases. It can quickly remove scar tissue and speed up healing.
Manufacturing diagram of a large flat coil 250 mm
Option 1 (when using a standard generator with a power of up to two watts)
We connect the oscilloscope probe in parallel to the generator terminals.
We gradually increase the frequency of the generator and look for the first frequency at which output voltage generator is the smallest. This will be the operating frequency of this capacitance.
Option 2We connect a resistor with a voltage of 1 Ohm in series in the power circuit.
We are looking for the first highest value amplitudes.
Option 3 (if you don’t have an oscilloscope)We make a flat inductor, the load of which includes 2 counter LEDs.
We look for the frequency based on the maximum luminosity of the LEDs.
For the above capacitance design, the approximate frequency is 280-320 kHz. In this case, the effective power range lies within ±10 kHz relative to the operating frequency.
A large flat coil allows you to work effectively at the level of the central nervous system, eliminate circulatory problems and many other small vortex problems of living organisms.
Scheme for manufacturing a toroidal coil (torus)
We make two taps from the coil: we take the end of one wire from inside the coil and the second from another wire outside. In this case, the circuit remains open, and the two unused outputs of the plates are simply cut off.
Option 1 (when using a standard generator with a power of up to two watts)
We connect the oscilloscope probe in parallel to the generator terminals.
We gradually increase the frequency of the generator and look for the first frequency at which the output voltage of the generator is the lowest. This will be the operating frequency of this capacitance.
Option 2We connect a resistor with a voltage of 1 Ohm in series in the power circuit.
We are looking for the first largest amplitude value.
Option 3 (if you don’t have an oscilloscope)We make a flat inductor, the load of which includes 2 counter LEDs.
We look for the frequency based on the maximum luminosity of the LEDs.
For the above capacitance design, the approximate frequency is 280-320 kHz. In this case, the effective power range lies within ±10 kHz relative to the operating frequency.
The toroidal coil copes well with crystalline slags such as stones and sand. Thor also eliminates pain symptoms and works well with wound healing.
The action of the Mishin coil causes the release of a significant amount of toxins, which must be eliminated by the kidneys through urine. Coping with this amount using vortex medicine is not an easy task for the kidneys, so coil treatment should begin with the lumbar region. There is the main human filter - the kidneys. Every second person has problems with their kidneys. We start by cleansing the kidneys, which must subsequently cope with cleansing the entire body.
The duration of the work session is determined by personal feelings after and during use of the coil. For example, we place the Mishin disk in the kidney area for half an hour. If after use you feel unwell, have some pain, or have a fever, then the Mishin coil has begun to work. If the discomfort is bearable, you can leave this dose for tomorrow. If you feel too bad, take a break for a day or two. For those who are overweight, the coil has a weaker effect at first. Electrostatics has a certain charge, which is consumed as waste breaks down deep in the body. She destroys looped formations in her path and exhausts herself with this. The next time, without encountering any obstacles in its path, the electrostatics penetrate further and cope with the next dose of the disease. Looped formations are largely located in fatty deposits. That is why overweight people need more time to get results from coil treatment. These people usually feel nothing at all for 3-5 days.
After you have felt the result from the action of the Mishin coil, you need to understand whether you can work with the coil in this mode, whether to add or reduce the exposure time. If you are on vacation, you do not need to go to work, for example, it is quite reasonable to give large doses of exposure the first time and get a very quick cleansing of the body. You can also go in a more gentle mode, using small doses. This applies to people who do not have any severe or acute illnesses requiring urgent intervention.
For local diseases, such as pain in the knee, head, etc., we can act differently. The torus (donut) has a targeted effect and is remarkably adapted for these purposes. The torus acts in approximately 10 cm in diameter.
There are things in the operation of the coil that will probably seem strange and inexplicable to most. The coil operates even when turned off, but only by about 20%. In addition, the impact occurs not only on the person on whom the coil is lying, but also on those who are within a radius of 3 and even 7 meters. Therefore, if you are treating someone, in order not to get an overdose, you need to move this distance away from the patient.
When a person completely gets rid of all toxins and other nasty things, the coil stops working on him. You can sleep on a coil, sit on it even around the clock, there will be no healing effect. This is precisely an indicator that you are healthy.
It's just brief introduction for safe use of the reel. For a deeper study, watch all the videos and read the material.
Questions and answers regarding the use of coils for treatment taken from the vortex medicine forums.
How safe is the coil treatment method??
It is quite safe if certain standards are followed. Even if the standards are exceeded, the danger is 10%, which is a low figure. It is better to observe safety precautions if there is a person in the same room with you.
treatment by a stranger. This does not apply to members of the same family, with the exception of children, since they have increased sensitivity to the effects. It is better to keep them away from the coils. You should be at a distance of 2-3 meters from the person undergoing treatment.
What do our coils look like on thin plans?
“They look like waves connected into a sphere. In the center of the sphere there is a space with a depth of the entire height of the sphere. The wave closest to the center of the sphere and near its exit develops the greatest force. If we consider a segment of such a wave, near the center and at the exit it will be 100% in strength, and between these two points in the middle it will be 70% in strength. Between two exits
an exchange takes place, and the disease goes away as a result of this influence. If the body is loaded with diseases, then there is not enough power to destroy them. Where the torus is placed, the work goes on more intensely. At the edges of the waves it is weaker from 10 to 30%. The image of the torus can be strengthened by imagination, this will make the waves more powerful and the disease will be easier to succumb to the action of the torus. But for this you need
have developed energy or learn to develop it in such work.
How our aura reacts to the influence of coils?
- The aura becomes larger and more holistic. She is irritated by the powerful action of the waves, open areas are closed, bridges with the lower worlds through which energy flowed are removed.
How the chakras of our body react to coils?
— The chakras rotate perfectly with them - they are like a motor for them.
What is the difference between on and off coils on thin plans??
- Both work. If comparatively, then on is 100%, and off is 20%.
Is there a qualitative difference in the reactions of children and adults to reels??
— Children quickly learn the fields of the torus (disk). For them, 2-3 times of 30 minutes of weak exposure is enough, provided that their health is not burdened by serious illnesses.
The coil emits, retracts, or both at the same time?
— It emits and draws in at the same time.
What are the differences between the operation of a torus and a disk? What is their impact area??
— Degree of identity 70%. Accordingly, the difference is 30%, and it is important. Thor heals organs. And the disk adjusts the general fields - the subtle fields of the body or the surrounding space, if work is done with it. The disc can also treat organs, but it will take longer.
The main area of influence of the torus- within a radius of 10 cm. If we take the entire space of action of the torus as 100%, then these 10 cm will account for 50% of the total amount of impact, within a radius of 1 meter - 60%, 2 meters - 80%, 3 meters -100%. This is the average data. In some individuals, the fields expand to 10 meters, and in especially rare cases to 20 meters. The more developed a person’s consciousness, the larger his biofield and the larger the radius of influence. Therefore, the impact zone will be different for everyone, but on average 2-3 meters. Also, the size of the coverage area is additionally influenced by the Earth’s field this place, where the coil operates, increasing or decreasing the size of the zone of influence.
Disc impact area almost the same, except for the distribution of the degree of impact within this zone. It is more uniform compared to a torus. Within a radius of 10 cm - 20%, within a radius of 1 meter -50%, 2 meters -80%, 3 meters -100%.
Does it matter which side the torus or disk is facing the body??
Doesn't matter much except for the head. It should be applied to the head in such a way that if you look at it from above, then the winding goes counterclockwise. For plants, it is better to place it so that the top is wound clockwise
« How to properly work coils with a body? Methods of working with diseases?
— A person has three main body control centers. They are located in the head, chest and abdomen. It is necessary to awaken these centers (chakras) with a disk or torus. Then the body will do its own work. It would be correct to place the main emphasis on working with the chest (in the middle of the chest between the nipples) and the abdomen (two finger widths below the navel), alternately changing positions. The stomach is the place where life force accumulates. By customizing it, you can increase vitality and restore health faster. But it is difficult to adjust if you do not work with the chest center,
since the correct energy balance is lost if you work a lot with one center. Therefore, you should alternate between chest and stomach positions. Treatment will be carried out competently if sufficient work has been done with the chest center.
Since in this center there is the main bridge of communication with the lower world, through which energy flows. When working with coils, this bridge is completely removed. Another bridge, 2 times less powerful, is located in the head space. Adjustment of the control center in the head with coils should be done after they have been brought to 60-70%
proper functioning of the abdominal and chest centers. The treatment regimen is ideally selected individually.
The scheme can be as follows: chest 10 minutes, stomach 10, chest 20, stomach 20, chest 10, stomach 10. The maximum treatment time at one location is 1 hour. But it’s better to limit yourself to 20-30 minutes. For the head – no more than 10 minutes.
Typically, the fullness of energy and the proper functioning of these three centers in sick people ranges from 5 to 30%, in relatively healthy people (those whose illnesses are of a mildly manifested nature) - from 30 to 50%. You can also find out your details at independent work pendulum. The total amount of time interacting with the coils is 1-2 hours for the first day and from 2 to 5 hours per day thereafter. Sessions can be 1,2, or 3 times a day, but it is better to do 3 times a day, dividing the total time into three parts.
For those who use coils on the body for 9-10 hours, although such work kills the disease, it causes great harm to the subtle fields of the body, the elimination of which requires the body to spend about 3 days, which takes additional energy.
What is fundamental in this treatment method??
For more than a century, humanity has been widely using electricity. Countless devices of all kinds have been produced. At the same time, no one thinks about their safety.
Over the past decades, the number of pathologies of the human body, the treatment of which cannot be treated by medicine, has increased. The reason is often not so much a poor environmental situation as a lack of understanding of the processes in all devices that operate on the basis of the phenomenon of electromagnetism.
If we touch on physical processes, then in nature they proceed in accordance with Speaking in simple language, the execution of an action is impossible without a fulcrum, and during its execution the object and the support receive equal mechanical impact. If you look at this problem through the prism of vortex processes, it turns out that when creating electromagnetic radiation, the electrostatic plane is taken as a basis.
The Mishin healing coil, reviews of which indicate that it has a high degree of functionality, provides vortex processes. They have a healing effect.
What does electricity radiation destroy?
Our life is full of continuous pulsations emanating from electrical devices. They have a destructive effect at the molecular level. As a result, increased energy saturation of molecules is caused, which leads to the formation of large clusters. Many looped structures of molecules in the human body cannot be treated with medications due to their high level of strength. Such formations in the body lead to the appearance of cancer or block any functions in the body.
The most unified method is to create a zone with a reduced density of the medium using electrostatic implosive resonance. This effect is provided by the Mishin healing coil.
The essence of her work is actually built on gravity. True, the range of the device is small. It is only 2-3 meters. The level of transmitted power of such equipment depends on the degree of voltage. The amplifier for the Mishin coil has an output voltage frequency of 12-24 volts. The current indicator should not exceed 100-200mA.
Principles of flat coil manufacturing (DMA)
How to make such a device as a Mishin coil with your own hands? A preliminary preparation of a base is required, on which double-sided tape should be glued. A round protrusion is installed in the center. Its diameter is 25 mm. Around it, the laying of two wires begins, which should lie parallel to the plane of the base.
The generator for the Mishin treatment coil can be of a standard configuration. Its power is quite enough for health purposes. The generator circuit for the Mishin coil is presented below.
After manufacturing such a device, a container is obtained based on a pair of spiral-shaped plates that are nested inside each other. It is possible to use any copper wire, the diameter of which, together with the insulation, will be no more than 1.5 mm. The diameter of the coil should not be more than 23-25 cm. The wire is fixed at the top. You can secure it with tape.
The Mishin coil, the circuit of which is not so complicated, can easily be assembled independently. The materials for its manufacture are easy to obtain at any electrical appliance store.
How to set up a coil using an oscilloscope?
Mishin's vortex coil needs to determine the frequency. For this purpose, a pair of taps are made from the device. You should take the end of one wire from the inside of the coil, and the other end from the outside. In this case, the circuit remains open, and the two terminals of the unused plates should be cut off.
When using a generator standard type, the power of which is 2 W, it is possible to determine the operating frequency of the device by connecting the oscilloscope probe in parallel with the generator terminals. while gradually increasing. The first frequency at which the generator output voltage is lower is determined. This will be an indicator of the operating frequency of this device.
Second voltage measurement option
The device can also be measured using a 10 m resistor, which is connected in series. The highest amplitude value should be determined. This method makes it possible to evaluate the quality level of the supplied sine wave in load mode in the tank.
How to configure using the LED indicator?
The operating frequency of the capacitance can be determined using an indicator coil. It is an induction device that includes two counter LEDs.
With this method, you can find the frequency by the maximum luminosity of the LEDs. In this case, the generator voltage decreases. This ensures a reduction in the frequency range at which the glow is observed.
Effective coil frequency indicator
If you ensure strong fastening of the wire and do not subject the device to severe mechanical deformation, then after installation optimal frequency power supply of the container, its frequency indicator will not change during use. For the container design presented above, average frequency is 310 kHz. In this case, the effective frequency range of the supply signal lies within ±10 kHz relative to the operating frequency.
Such a device has a wide electrostatic spectrum and a low gradient of plane change towards the center of the device during operation. This will allow you to effectively influence the central nervous system, eliminate circulatory disorders and many other vortex problems in the body.
Design features of a flat coil with a diameter of 12 cm
Mishin treatment coils with a reduced distance between the plates have a higher level of impact on pathogenic formations. For example, you can use a wire with a cross-section of 0.5 mm in varnish insulation. The length of each wire will be 10-12 meters.
The internal diameter will also be approximately 25 mm, and the external one - 130 mm. This capacity has a high level of efficiency. It can affect the smallest viruses, fungi, eliminate scars and accelerate the process of tissue regeneration.
Features of the torus configuration (TMA, donut)
A subsequent reduction in the cross-section of the wire and the overall size of the coil will lead to the creation of an even more effective version of the vortex capacitance. With an outer diameter of 51 mm and an inner diameter of 25 mm, a wire thickness of about 0.1 mm is created.
Such a device is difficult to make by hand. Therefore, it is recommended to use a simplified version of manufacturing the device in the form of a torus.
Making a torus
To make a torus, you will need about 15 meters of twisted pair cable (UTP 5E). The wire includes four or eight cores, which are twisted in pairs. You should remove the outer insulation of the cable and separate one pair from the rest.
To create such a container, you can use almost all types of wires. The only condition is that the distance between the wires along the entire length must be the same. Therefore, twisted pair is ideal.
Next, a piece of electric corrugation is used. It will become the basis for creating equipment for bobbin winding. The diameter of the corrugation should be 25 mm. It should be bent into a torus of the required size. A slot is made along the outside. It is secured with a couple of turns of insulating tape.
This winding will ensure the correct formation of vortices. In this case, a whole spectrum of frequencies is formed, where the inner part of the winding is responsible for high performance, and the outer part for low ones.
Before you start winding, the internal lead of the wire should be threaded into a pre-prepared hole in the corrugation, and after winding, fix the outer leads. To secure the winding, it is necessary to remove the corrugation in parts. Twisted pair leads unwind, and unused ones are bitten off
Determining the device power frequency
Next, you should determine the frequency of the torus power supply. The generator terminal must be connected from different sides to the wires of the device. To determine the output voltage, the oscilloscope probes are connected directly to the generator terminals.
Then the first indicator of the frequency of the maximum voltage drop relative to the input is determined. In other words, the frequency of maximum conductivity of the capacitance should be indicated. Further nutrition will take place precisely at this indicator.
Coil power supply
The coils are powered by a sine wave (signal from the generator). Power supply via pulses is unacceptable, since it does not have inertia in this mode. The high efficiency frequency range for toroids is the same as for flat coils. It is 270-380 kHz.
During operation of the device, the supply voltage coming from the generator can drop up to ten times or more. In this case, the total power supply activity indicator can be no higher than 0.1 W. The maximum conducting current power should be limited to 200 mA, and the voltage to 22-24 V.
If these parameters are overestimated, this can lead to electrostatic breakdowns, which will be expressed in discharges from the center of the coil.
What generators should I use?
A frequently used generator for the Mishin coil is TGS-3. It has automated resonance tuning.
The ATTEN ATF20B+ model is considered a more professional analogue. Its advantages include the presence of a display, USB interface, frequency counter, waveform. Such a generator for the Mishin coil emits a signal that is not subject to distortion.
Mishina coil treatment
So, by preparing a device of the simplest configuration in the form of an inductive coil, it is possible to influence any problem areas of living organisms for therapeutic purposes. In most cases, knowledge of painful points in the body is not at all necessary, since electrostatics automatically affects painful volumetric structures and contributes to their separation.
What is vortex medicine based on? Mishin coils provide natural application of environmental energy to influence the problems arising in the carbon form of life. This method is equivalent to the effects of antibiotics, and also serves as a replacement for operations to remove cancerous tumors. The vortex flows created by the coil will easily restore the affected nerve cells.
What did the testing of the device show?
What potential does the Mishin coil have? Treatment with it gives good results. Tests carried out over a number of months revealed high level the effectiveness of using electrostatic capacitance to restore lost body functions. The duration of one session, depending on the disease, ranged from 5 minutes to an hour.
Features of the treatment of certain diseases
The Mishin coil causes the release of large amounts of toxins, which must be eliminated by the kidneys through urine. Dealing with so many harmful substances when using a coil is not an easy task. Therefore, treatment begins with the lumbar region.
For normal mode For cleansing the body, sessions lasting 30-40 minutes will be sufficient. They should be carried out within the first five days. The coil is applied to the lumbar and chest area. The lower back is the most important area of influence during treatment, as the kidneys are cleansed. These organs, as statistics show, are severely clogged in half of the people.
The first week of treatment contributes to significant cleansing of the body. The immune system works in enhanced mode, tissue regeneration begins.
The duration of sessions held in the second week can be increased to 60-90 minutes. This is the average. Much depends on the specific case and disease.
For example, kidney treatment should be carried out in sessions lasting half an hour. If after the procedure the patient complains of feeling unwell, weakness, chills, fever, pain, then the Mishin coil has begun its effect. If a person is able to bear the discomfort, then a similar session is carried out the next day. If you feel very bad, it is recommended to postpone treatment for two days.
Each person is able to determine what intensity of exposure he needs to be cured. The patient chooses the duration of the session individually.
At first, the coil may have little effect on obese people. Electrostatics have a certain charge that is consumed as waste products break down in the body. It promotes the destruction of looped formations. During the next session, without encountering any obstacles on its way, electrostatics penetrates even deeper and copes with the disease. Cell formation, as a rule, is located in the fat layer. This is why overweight people require a longer period of treatment. Typically, such patients do not feel any results from the sessions within the first five days.
Choosing the right mode
After the Mishin coil begins to act, you need to decide whether this mode is right for you, whether it is worth adding exposure time or whether it should be reduced. If you are on vacation, you can resort to daily long-term procedures. This way you can cleanse your body in the shortest possible time. It can also be used in shorter sessions. This intensity is applicable to people who do not have any severe acute illnesses that require urgent treatment.
A local disease, for example, pain in the knees or migraine, can be treated with another device - a torus. This bagel has a targeted effect and is perfect for these purposes. The impact diameter of the device is approximately 10 cm.
Features of the coil
There are nuances in the operation of the coil that are difficult to explain.
For example, the coil continues to work even when turned off. Only the indicator of its functionality in this case is 20%. In addition, the impact extends not only to the person to whose body the coil is attached, but also to people who are at a distance of 3-7 meters from it.
Many people are interested in how long a device such as a Mishin coil can be used. Treatment should be stopped after the body has rid itself of all toxins, as the device no longer has any effect on the body. You can apply the coil to your body throughout the day, but it will not have any effect. This is what will indicate that you have improved your health.
