Where to turn on Wi-Fi on Windows 10. Turning on Wi-Fi

Sometimes Windows 10 reports that there is no or limited connection; such messages appear after installation or updating the system, as well as during normal operation. In this step-by-step instructions, we will describe ways to solve problems with the Internet connection and figure out why WiFi does not work in Windows 10.

These methods are suitable if you have the correct router settings and no problems have been detected by the Internet provider.

If there is no connection after updating the system, you will need to do the following:

Check whether all the necessary protocols for the connection to function are enabled in its properties. To do this, press the keyboard shortcut "Windows+R" and enter ncpa.cpl into the window that appears.
Click « OK » .
Go to "Properties" connection that you use to access the Internet from its context menu.
For normal network operation, at least the protocol must be enabled IP4. But in general, it is recommended to enable all protocols.
Check the protocol box IP4.
Click "OK" .

In addition to the reason described above, the connection may be blocked by your firewall or your firewall. In this case, you will need to completely remove these applications, preferably using the official uninstall utilities from the developer’s website. After this, restart your PC and check the Internet.

Also, the reason for the lack of connection may be broken Wi-Fi drivers. The tenth Windows itself often updates them, and may install inappropriate ones.
In this case, you will need to install drivers downloaded from the adapter manufacturer's website.

Note: If before this the same driver functioned normally, but now it does not work, you can return it back by clicking the rollback button in its properties.

Another way to help resolve problems is to turn off the economy mode. To do this, you will need:

Another step if none of the above methods helped is to check if the protocol is enabled IP4 in Wi-Fi properties, and return the settings to default. For this you will need:

Also, disabling the protocol can sometimes help troubleshoot connection problems. IP6.

In addition to the command described above, you can additionally set settings that can help solve the problem. Enter them in the specified sequence and after each click "Enter" .

After this, reboot the system.

Another method you can try to troubleshoot Wi-Fi problems in Windows 10 is to disable the FIPS standard. You can do this by following these steps:

That's all, we hope that using these instructions you will be able to solve your problem with Wi-fi connection.

A huge number of people can no longer imagine everyday life without the Internet. But in order to use it, you first need to connect to the World Wide Web. It is at this stage that some users periodically experience difficulties. In this article, we'll tell you what to do if your Windows 10 device won't connect to your Wi-Fi network.

Today we will talk about two main methods that will help you solve the problem of connecting to a wireless network. In fact, there are many more similar methods, but most often they are individual in nature and are not suitable for all users. Now let's look at both mentioned methods in detail.

Method 1: Checking and enabling the Wi-Fi adapter

In any unclear situation with a wireless network, you first need to make sure that the adapter is correctly recognized by the system and access to the hardware itself is enabled. It sounds trivial, but many users forget about this and look for the problem too deeply at once.

Open "Options" Windows 10 using keyboard shortcut "Win+I" or any other known method.
Next, go to the section "Network and Internet".

Now you need to find a line with the name on the left side of the window that opens "Wi-Fi". By default it is second from the top. If it is present in the list, then go to this section and make sure that the wireless network switch is set to "On".

In case the section "Wi-Fi" not in the list, should be opened "Control Panel". To do this, you can use the keyboard shortcut "Win+R", enter the command control in the window that opens, and then click "Enter".

About how you can still open "Control Panel", you can find out from a special article.
A new window will appear. For convenience, you can switch the element display mode to "Large Icons". This is done in the upper right corner.

Now you need to find an icon with the name in the list "Network and Sharing Center". Go to this section.

In the left part of the next window, click LMB on the line "Changing adapter settings".

At the next step, you will see a list of all adapters that are connected to the computer. Please note that additional devices that were installed on the system along with the virtual machine or VPN are also displayed here. Among all the adapters you need to find the one called "Wireless network" or contains the words in the description "Wireless" or "WLAN". Theoretically, the icon of the required equipment will be gray. This means it is turned off. In order to use the hardware, you need to right-click on its name and select the line from the context menu "Turn on".

After completing the described steps, try again to search for available networks and connect to the one you need. If you do not find the adapter you are looking for in the list, then you should try the second method, which we will discuss later.

Method 2: Install drivers and reset connection

If the system cannot correctly detect the wireless adapter or its operation is malfunctioning, then it is worth updating the drivers for the device. Of course, Windows 10 is a very independent operating system, and often installs the necessary software itself. But there are situations when equipment needs software released by the developers themselves for stable operation. To do this, we recommend doing the following:

After restarting your computer, try connecting to Wi-Fi again. In most cases, the described actions solve previously encountered problems. If you are trying to connect to a network whose data is saved, then we recommend activating the function "Forget". It will allow you to update the connection configuration, which could simply have changed. It's very easy to do this:

We hope that by following the steps described, you will get rid of various errors and problems with Wi-Fi. If after all the manipulations you were unable to achieve a positive result, then you should try more radical methods. We talked about them in a separate article.

Windows 10 is the next step in the evolution of operating systems for desktop and desktop computers from Microsoft Corporation. Despite the fact that Windows 8 can be considered a failure, its release was still beneficial for developers. Windows 10 has absorbed all the best from all its predecessors and acquired an incredible number of new features and capabilities. Some of their list also relate to the functioning of a wireless network, so setting up Wi-Fi in a Windows 10 environment can cause problems for beginners who have purchased a device that operates on its basis.

In today’s article, we’ll look at how to set up Wi-Fi in 10, connect to an existing wireless network, and the problems associated with it.

Turn on the radio module

Before using a wireless Wi-Fi connection on a laptop, you need to activate the WiFi module. This is done using a special hardware key or key combination, for example, Fn and F11 (see the manual or look for the corresponding icon on the buttons or keyboard of the laptop).

Connect to an active access point

Here is an algorithm of actions that the user will have to perform in order to connect to the broadcast WiFi point. Naturally, to do this, you need to know the connection password, if it is set, and enable the use of the radio module on your device running Windows 10.

Click on the network icon located in the tray.
Select the appropriate wireless connection and click on it.

Check the “Connect automatically” checkbox if you are using this access point as a permanent connection, and click “Connect”.

If you have a password consisting of 8 or more characters, enter it and save it if necessary.

After checking the data, passing authentication and initialization, the Windows 10 computer will be connected to the specified Wi-Fi point. As you can see, establishing a connection via a wireless network in the “ten” is almost identical to previous versions of the OS.

See also: How to unblock the publisher of Windows 10

Additional wireless settings

Windows 10 is distinguished by a considerable list of Wi-Fi parameters and its capabilities available to the user: viewing connection data, configuring security settings, configuring sharing, file sharing, remote access and viewing saved passwords.

Looking at the saved keys

Windows 10 provides the ability to view the password for the network to which your device is connected, for example, to connect to Wi-Fi using a smartphone or to transfer the key to a friend.

It's sad, but you won't be able to view the saved password for an inactive network.

To do this, go to the “Network Control Center...”.
In the “View active networks” frame, find “Wireless...” and click on its icon.

Call up the properties of the active WiFi connection.
In the “Status” window, click on the button indicated in the screenshot.

A window will appear with detailed information about the WiFi connection currently in use.

Go to the “Security” tab and activate the function of visualizing the characters entered in the security key field.

On the Windows 10 computer from which you configured the Wi-Fi router, you can also view the wireless connection encryption key.

Follow what is indicated in the user manual or on the sticker on the back/bottom cover of the router.

Typically this is 192.168.0.1.

Click on the “Wireless Mode” link.

In the “Protection...” or “Security” tab, move to the connection encryption method and see the key in the “PSK Password” field.

Removing an unnecessary connection

Even with a one-time use of a public network (in a cafe, airport), Windows 10 remembers the parameters of the connection made and stores them. If such a network is not needed in the future, it can be easily deleted - “forgotten”, so that the computer does not connect to it.

Call up the “Networks and Internet” menu item in the system settings.
Go to the first tab “WiFi”.
Click on the “Manage settings...” button below.

See also: When installing Windows 10 I started getting an error

Scroll down the list until you see the names of the access points.
Click on the name of the unnecessary wireless network and click “Forget”.

From now on, when a forgotten connection is detected, Windows 10 will not make automatic connections to it.

Creating a new connection using a TP-Link router

Forming and setting up a new connection in Windows 10 is a simple procedure and it depends, first of all, on the router used, and not on the OS version. In principle, how to configure the router is described in its instructions, but let’s briefly look at the process of creating a new WiFi connection.

We turn on the device to the power supply and connect it to the computer using the included crimped twisted pair cable.
We are waiting for the router to load.
Open an Internet browser window and enter the starting address (look on the sticker on the case or in the user manual) to enter the router interface.
Enter the standard password and login values to gain access to the interface.

Typically this is "admin" for both lines. In any case, take a look at the technical documentation.

Go to the “Quick Setup” tab.

Using the functionality and tips of the wizard, we set the key Wi-Fi parameters.
Be sure to save the settings and reboot the router if the device reboot does not start automatically.

This concludes the review of the main features for working with WiFi in Windows 10.

(Visited 12,916 times, 45 visits today)

windowsprofi.ru

How to set up Wi-Fi on Windows 10: connecting to a network, viewing the password

Windows 10 was a continuation of the ideas of Windows 8, adopting good qualities from it and further adapting to simultaneous work with both classic controllers like a mouse and keyboard, and with new touch screens focused on finger control. However, users who have just gotten used to working with 8 will need to adapt again to the changed appearance of Windows. Because of this, operations like setting up Wi-Fi on Windows 10 can be difficult for untrained people.

Connecting to an existing network

First, let's figure out how to connect to an already active broadcast Wi-Fi network. First, you should make sure that the activation button of the wireless adapter is in the on position. After turning on the module, you need to connect to the Wi-Fi network, for which you will need:

After these manipulations, the computer will be ready to work with web pages. As you noticed, connecting to Wi-Fi on Windows 10 is just as easy as in previous editions of the OS.

Interaction with networks

Windows is popular among users because it provides the ability to fine-tune almost every parameter. If necessary, with a little effort, the user can independently configure the OS functions as he sees fit. The same applies to the rich functionality for setting up networks: look up the IP address, set security and sharing parameters, transfer files to other computers on the same work network - all this could be done in previous generations of Windows and in the new Windows 10.

The new OS also contains functions that allow you to find out the key to the connected network. So, if a user needs to see the Wi-Fi password on Windows 10 in order to tell it to another person, then it is necessary:

Forget saved network

You can also completely forget the Wi-Fi network on Windows 10 so that the computer does not connect to it on its own when it is available again. To do this, the user needs:

In turn, you can create a Wi-Fi network on Windows 10 in the same way as it was done in previous editions of the OS. This operation no longer falls on the system, but depends on the router used. Instructions for creating and configuring a network are always included with the router; according to general rules, it looks like this:

The user needs to connect the network cable to the router, and plug the device itself into a power outlet and activate it.
Wait until the necessary indicators on the device body light up.
Go to your computer and check the list of broadcast networks.
Connect to an access point whose name matches the name of the router you are using.
Open an Internet browser and go to the router’s web interface page. Depending on the device model, this may be the address “192.168.0.0” or “192.168.0.1”, but this parameter is individual for each manufacturer, and here it is better to use the operating instructions.
Log in to the router menu using the standard login-password pair. This parameter also depends on the manufacturer.
Use the Quick Setup Wizard. Most routers have this function, including budget models. Following the program prompts, the user will sequentially set all the necessary network parameters, including its name, password and the number of devices that can connect to this access point at the same time.

Important! After the setup is completed, save the changes, since many router models tend to reset the settings to factory settings after shutdown and do not save the specified data automatically.

Also, access to the Internet often requires action on the part of the provider - this also needs to be checked with the company providing access to the World Wide Web.

Conclusion

So, Windows 10 provides all the same tools for managing your Internet connection as previous versions of the OS. To a large extent, the differences lie only in the visual design of some sections of the settings menu and their adaptation to touch control.

WindowsTen.ru

Setting up Wi-Fi in Windows 10

To easily create a software WiFi router in Windows 10, you need to:

Windows 10 OS.
WiFi adapter.
The presence of the Internet itself.

The article looked at an ADSL connection as an example. But in reality, you can use absolutely anything: PPPoE, Wi-Fi from a second adapter, and so on.

To configure wifi distribution via the command line (cmd), use the commands:

netsh wlan set hostednetwork mode=allow
netsh wlan set hostednetwork mode=allow ssid=FastWifi key=12345678 keyUsage=persistent

The procedure for setting up a Wi-Fi network is as follows:

First, you should check whether the Wi-Fi router is working. For example, on laptops the virtual WiFi adapter may well be disabled in the BIOS itself. On laptops, to make sure it works, you can use the Fn+Fx or Fn+F3 keys. But the easiest way to check is by clicking on the “Network” icon and checking if any other networks are available. If yes, then everything is in order (if someone nearby is giving access).

You need to make sure that there is unhindered access to the network. The console will help with this, in which you need to enter the “ping” command, or by opening any browser. This way we will make sure that we can distribute the Internet.

You should make sure that the “WLAN Service” is running, including “Routing”. This can be done as follows: Control Panel, then go to Administration.” The standard service settings should start automatically. However, there are cases when, after optimizing a PC, specialists turn them off. With this optimization option, specialists can often harm the operating system, and it will be difficult to try to distribute the Internet.

After making sure that the services are working, you need to launch the Windows console with the “cmd.exe” command with all administrator rights. The best option would be to open WinX in the operating system menu. It contains “Command Prompt (Administrator)”. You can open it using Win+X.

Opening the Windows 10 OS console, enter:

netsh wlan set hostednetwork made=allow ssid=winap key=123456789 keyusage=persisstent

The command creates a wireless point with the following parameters:

winap network name;
Password 123456789.

It can be copied from this article to save time. It looks like this in the image:

Instead of “winap” and “123456789”, you may need to enter your desired name and password, respectively, which you are going to use when accessing Wi-Fi. This will not only protect your network from hacking, but will also prevent you from forgetting your password and access name.

It is worth paying attention to the fact that: the password for accessing the wireless network should consist of no more than 8 characters; the Cyrillic alphabet does not need to be entered to avoid confusion.

After the work is done, you can try to distribute wireless Internet. In the same console you should enter:

netsh wlan start hostednetwork

netsh wlan show hostednetwork

The last of them displays the presence or absence of access to the Internet. This can be seen in the image:

Upon completion of the check, you should go to “Network Connections” in Windows 10 using the Control Panel.

In this example, “Ethernet” is the source of the Internet network. In this case, “Local Area Connection 3 winap” is an access point. It is in working condition. It is recommended to assign a new name to the wireless network so as not to confuse it with anything else in the future.

After this, you should expand your Internet connection using “Windows ICS”. To do this, hover over the connection (in the photo it’s “Ethernet”), then right-click, after “Properties”, then go to the “Access” tab. Ultimately, he clicks to enable ICS and establish a connection with the one who is trying to distribute traffic - to WiFi “winAP”.

Upon completion of all actions, we connect to the WiFi network and check whether the Internet can be distributed or not. In the console you can run the command

netsh wlan shaw hostednetwork

It shows how many users are currently using your Internet distribution with all their might.

How to manage an access point

By performing certain actions you can control the access point, namely:

netsh wlan stop hostadnetwork

The command stops the wifi network.

netsh wlan set hostednetwork mode=disalow

The command completely deletes the access point data from the system. This is done instantly and there is no provision for a reversible process.

netsh wlan start hostednetwork

The command sets up automatic network starts. Thus, it is added to startup. Moreover, it is allowed to be written into a cmd script. All that needs to be done for this is to indicate that it is launched as an administrator (otherwise this will not be possible), and then add the script to startup. Please note: it is required that wireless network access is also installed when downloading Windows 10 version. Otherwise, despite the functionality of the access point, there will be no Internet.

Without any doubt, it will take no more than 5 minutes to start distributing the Internet in this way. However, this does not require the use of additional special programs. This method of connecting a network allows you to create a WiFi router in a short time without any hassles and distribute the Internet. Moreover, you can use it anywhere and any time of the day. If you plan to use the network access point every day, the best option would be to purchase a router. Since this option is convenient only for those who use it on work trips, or even need it several times a month.

Possible problems

If it happens that the Wi-Fi wireless network is not working without any reason, the Windows 10 operating system should not be blamed for this, the problem is clearly located in the settings. Some of the popular problems in this case are:

WiFi router drivers – it is advisable to reinstall them.
The problem is in the router itself.
Perhaps the actions were carried out incorrectly.
Perhaps all services that are responsible for access are disabled.
There may be a virus on your computer that is stopping it from working.

For example, when starting the operating system, the Wi-Fi router driver may not ask the virtual adapter to exit standby mode. When the Windows 10 system boots, the service continues to be in this state.

The procedure for creating and configuring a WiFi router access point to a wireless network can also be applied to Windows of earlier versions, in particular version 8 and 8.1.

Found a typo? Select the text and press Ctrl + Enter

ZnaiWifi.ru

How to connect to Wi-Fi on Windows 10?

Lately, everyone has been writing about Windows 10. Some criticize it, others really like the system, everyone is updating, testing and all that. I also try to be in the “trend” :), so I put the ten next to the already installed Winodws 7, and used it a little. Well, of course, I checked how Wi-Fi works, and how network management is generally organized. Even compared to Winodws 7, practically nothing has changed, there are just some more settings that are tailored for touch screens.

The panel for connecting to Wi-Fi networks has changed a little; now you can turn Wi-Fi on or off in just two clicks. The main thing I liked was the automatic installation of all drivers, including for the network card and Wi-Fi receiver. On my laptop, a model like 2013, all the drivers were installed automatically. I really don’t know how it will be on other computers, but this is very cool, because on the same Winodws 7, there have always been many problems connecting to Wi-Fi, precisely because of the drivers. The only thing I haven’t found is where to look up the password for the Wi-Fi network in Windows 10. The method I wrote about in this article is not suitable. There simply is no "Manage wireless networks" item. I’ll study this topic a little more and write about how to remember the password on the “ten”.

In this article I want to show you how to connect to Wi-Fi on Windows 10. I’ll also show you where the wireless network settings are located.

Connecting a laptop or tablet on Windows 10 to a Wi-Fi network

Everything is very simple, and also beautiful. On the notification panel (in the lower right corner), click on the button in the form of network divisions (Wi-Fi antennas). If you have a Wi-Fi driver installed, but the adapter itself is turned off, then the icon will have a red cross, and if there are networks available for connection, it will have an asterisk.

Click on this icon, and if Wi-Fi is turned off, then click on the corresponding button and turn on the wireless adapter.

Immediately after turning on the wireless adapter, the networks available for connection will appear at the top. Click on the desired network and click on the Connect button. You can uncheck the Connect automatically option if you do not want your device to establish a connection to this network itself.

If the network is protected by a password, you will need to specify it.

Next, the system will ask if you want your computer to participate in your home network. Other devices will see it. If you are connecting to your home network, I recommend clicking Yes. So that later there will be no problems with setting up the local network.

That's it, your computer will be connected to the Internet. By clicking on the network you are connected to, you can easily disconnect from it.

You can finally test the new browser - Microsoft Edge. An interesting browser by the way, I would like to see your reviews about it.

How to open Wi-Fi settings on Windows 10?

Click on the connection icon and click on the Network settings link.

The "Network and Internet" settings will open. There are wireless network settings.

You can also open the familiar network and sharing control panel. Just right-click on the connection icon and select Network and Sharing Center. And then everything is the same as in Windows 7 and 8, managing adapters, etc.

So far I have not heard about any problems with Wi-Fi on Windows 10, errors, crashes and the like. Well, by tradition, the most popular problem is “no Internet access”, or rather the connection status is “Limited”, with a yellow triangle next to the network icon. As a rule, the router is to blame. Or rather, incorrect setting. If you have such an error, then see the article: “Connection is limited” in Windows 10 via Wi-Fi and network cable.

I would be grateful for your comments on the topic of the article. Write how you like Windows 10, whether there are any problems with accessing the Internet via Wi-Fi, or about any new features of the system.

help-wifi.com

How to connect Wi-Fi on Windows 10?

Without a doubt, the release of a new version of the popular operating system became one of the main events of 2015 in the field of IT technologies. Following months, which for many users felt like an eternity, a flurry of criticism, discussions and questions followed. Of course, most users, after installing the update, rushed to check what they had added to the main functions of the “ten”. Of course, one of the main functions of the OS is connecting to a wireless Internet network. In general, the creators did not introduce anything extraordinary into the operation of Wi-Fi. In addition, many similarities in this component can be found with a similar process in its predecessor versions. But, as you understand, this would not be a new OS if the functions and settings were left without innovations compared to Windows 7 and 8. Today we will talk about the benefits of Wi-Fi and how to connect Wi-Fi on Windows 10.

New Wi-Fi features in Windows 10

In general terms, this element has a modified panel for connecting to wireless networks. In particular, turning Wi-Fi on and off can be done in two clicks.

What we can praise the developers for is the integration of such an option as automatic installation of all drivers.

How to create a restore point in Windows 10?

How to prepare a laptop and tablet for connection?

In principle, there is nothing abstruse in this process - fortunately, the creators decided not to reinvent the wheel and did everything beautifully and simply. We go down to the bottom of the screen, where the notification panel is located. Click on the wireless network icon. If the adapter is turned off, there will be a red cross on the icon. In the case when both the adapter and the driver are in perfect order, the icon will have an asterisk. Therefore, to connect to the Internet, you should select a specific network and click on it.

After this, a “Connect” button will appear under the name of the potential Internet “supplier” network. In addition to this, you will also see the “Connect automatically” option, which you can check if you want your laptop or PC to independently connect to the selected network.

Of course, in most cases, wireless network distributors set a password for their network, so after connecting, the system will ask you to enter the network security key. After entering it, a request will appear asking you to allow other PCs to detect your device. In this case, it is better to give a positive answer in order to avoid future embarrassment with setting up a local network. That's it, now your device is ready to receive a signal.

Calling up wireless Internet settings. View Password

At the end of the list of available networks there is a “Network Settings” link. After clicking it, the “Network and Internet” subsection will appear, in which you can enable or disable network access, select a network and make settings in the “Advanced Settings” item.

As for the security code, users often experience some difficulties with it. This question is especially relevant for those who use one router from several devices. To achieve your goal you need to follow a couple of simple steps. First, go to the “Network and Sharing Center” section, which can be accessed using the Control Panel. In the window that appears, select the “Wireless Network” link (located in the upper right corner), then select the “Wireless Network Properties” button.

How to clean the Windows 10 registry?

After this, the “Connection” and “Security” tabs will appear, go to the second one.

The password is typed opposite the line “Network security key”. In order to see the characters, you need to check the box next to the “Display entered characters” item.

How to forget/create a network?

In order for your device to stop connecting to a certain network on its own as soon as it is active again, you need to go to the “Settings” section, the “Network and Internet” subsection and select the Wi-Fi option. In the window on the right, select “Manage Wi-Fi network settings.” A list of known networks will appear in front of you, from which you should select the one you want to forget. Actually, after clicking on the name of the network, the system will offer to perform the desired action.

Thus, the system will exclude the selected network from the “registry” and the independent connection will stop.

The process of creating a network is no different from its predecessors.

Make sure your router is active, then look through the list of available networks. As soon as you see a name in this list similar to the name of the router model, connect. Then go to your browser and open the router's web interface page. After that, enter your username and password to access the menu. In the menu you can already use the quick preparation wizard, which will tell you all the necessary instructions for creating a new access point.

Advantages and Disadvantages of Wi-Fi Connection in Windows 10

In general, there are no numerous (or even isolated) complaints about connecting to a wireless network in the Top Ten yet. The developers tried to make sure that life was not complicated for users and harmoniously integrated their innovations into the process. As you can see, having learned about some of the nuances of the principle of connecting a computer to a network, it is unlikely that in the future the system will prevent you from safely browsing web pages from the device.

The biggest problem with connecting to Wi-Fi, which is also present in previous versions, is the evil yellow triangle with an exclamation mark. It often frustrates users, but the system is not to blame. The “Restricted” status appears due to malfunctions of the router. And this, as they say, is a completely different story. How to fix the error “Windows cannot be installed on this disk”?

In one of our next articles we will tell you how to find out the Wi-Fi password.

If you still have questions on the topic “How to connect Wi-Fi on Windows 10?”, you can ask them in the comments

Was the material useful to you? Leave your review or share on social media. networks:

(2 ratings, average: 3.00 out of 5) Loading...

Wi-Fi is a universal solution for home and office in the age of wireless technology. Everyone has a smartphone, tablet and/or laptop and a router with high-speed unlimited Internet access. One day you may find that access to the Network has disappeared, although the Internet service is still available.

Secure network without Internet in Windows 10

In Windows 8/10, when the Internet is not working, a wireless network error may be accompanied by the message “No Internet connection, secure” or the message “Unidentified network”. This happens when, after successful work for many days, the Internet suddenly stops working.

Windows 10 message about suddenly lost access to the Network

But the “Protected” status is an indicator of working WPA-2 encryption; the “Protected” inscription appears on all detected wireless networks that are closed from unauthorized access with a software key. Consequently, its other semantic part - “No Internet connection” - reports that access to Network resources has been lost either on the router itself or on this PC/laptop/tablet.

The error “No Internet connection, protected” is specific to Wi-Fi networks, but “Unidentified network” is a common case for all networks, including cable.

You can try to fix the error by restarting Windows 10, turning off and then turning on the router, and also by unplugging and inserting the provider cable (or USB modem - when using mobile Internet). But when the problem is more serious, use the instructions below: the error “No Internet connection, secure” is only part of the overall problem, the solution of which must be approached comprehensively.

Checking IP settings and Wi-Fi components

To solve the problem with connecting to the Internet via Wi-Fi, first of all, pay attention to the network connection settings.

Give the command “Start - Control Panel - Network and Sharing Center - Change adapter settings.”
Unrecognized Wi-Fi network in Windows 10
Give the command: right-click on the Wi-Fi connection icon - “Properties” and on the “Network” tab give another command: “IP version 4” - “Properties”.
Protocols and services in Windows 8/10 connection properties
Make sure that the "Obtain an IP address automatically" and "Obtain a DNS address automatically" options are enabled.
To begin with, do not assign any IP addresses.
Close all windows by clicking OK, restart Windows 10 and check if the Internet is working (the message “No Internet connection, secure” should change to “Connected, secure”, or simply “Connected”). Launch your browser and go to a website.
If the same error appears again, then return to the same IP settings and enter the DNS addresses from Google - 8.8.8.8 and 8.8.4.4, or other public DNS addresses (for example, from Yandex). Save this setting, restart Windows 10 and test the connection again.
Enter the IP addresses of your network from the numbering range of the router as the main IP addresses, for example, 192.168.1.* (you cannot enter an IP value close to 1 in the last section - most often they take values 101–200). The subnet mask is automatically registered by Windows, but the gateway address is the IP of the router itself, in this example it is 192.168.0.1. Save the setting, restart Windows and check again if the Internet is available.

Restarting Wi-Fi in Windows 10

You can restart the Wi-Fi adapter in any version of Windows, starting with XP, by giving the command: right-click on the Wi-Fi icon - “Disable” in the already familiar network connections folder.

The shutdown command in Windows is the same for all network adapters

The “Enable” command is given in the same way. Similarly, you can disable and enable Wi-Fi from the sidebar of Windows 8/10 - either using airplane mode (all wireless networks will be turned off, even Bluetooth), or the Wireless network switch.

Turn off and on your Wi-Fi connection

If you simply disconnect from your wireless network, this action will not restart the Wi-Fi adapter. This is about the same as unplugging the cable from the LAN port - if you were using a cable connection rather than a Wi-Fi connection.

You can also “plug” a working adapter as follows.

If you previously used a PC, laptop or tablet as an Internet “distributor” (for example, with a 4G modem), in the list of devices next to the real Wi-Fi adapter there may also be a virtual one, signed as “Virtual Wi-Fi miniport adapter from Microsoft." It creates and maintains another Wi-Fi connection in the network connections folder. In this case, you need to manage not a virtual, but a real Wi-Fi connection - this is the built-in network card or external USB Wi-Fi module that you are working with.

Changing Internet Properties in Internet Explorer

Many browsers - such as Internet Explorer, Opera, Microsoft Edge and Avant Browser - allow you to configure additional browsing options.

Setting the Federal Information Processing Standard (FIPS)

Enabling FIPS technology, which provides additional levels of personal data protection, can help you.

Setting the network address for the Wi-Fi adapter

Network Address, or the adapter's network address, is a hexadecimal program code assigned to your network device, be it a wireless adapter or a LAN port on a PC's network card.

Turning off power saving mode

Power saving mode turns off unused devices, including data transfer via Wi-Fi.

Give the command: right-click on “Start” - “Power Management”.
Windows 10's secondary main menu lets you quickly jump to basic settings
Select the current power mode and click on the “Configure power plan” link.
Go to the power settings of the selected mode in Windows
Click on the "Change advanced power settings" link.
The battery life of your laptop depends on which unnecessary devices you turn off.
Turn off maximum power saving for the Wi-Fi adapter.
Wi-Fi will consume minimal electricity when there is no traffic

If there is no data transfer (for example, access to the Network is lost due to an error in the router settings), the Wi-Fi radio transmitter will turn on much less often (within the Wi-Fi network standard) than if it worked at maximum speed, sending and receiving gigabytes of data per hour.

Update, reinstall Wi-Fi driver

If it makes sense to update drivers, it is only when the manufacturer of your laptop or tablet has released updates for them. The Windows 10 system - especially its latest build 1709 (Fall Creators Update) - already contains drivers for all old and most new Wi-Fi modules.

If a new driver version is released, do the following.

Launch the already familiar Windows 8/10 Device Manager and give the “Update Drivers” command.
Driver update is necessary if there is a new version
Select to search for drivers in specific folders.
Manual installation will help install exactly the version you just downloaded
Specify the folder in which the already downloaded driver is located. The files must be decompressed if they were placed in a compressed ZIP folder.
Driver files should not be zipped
If the driver update is successful, the Device Installation Wizard will notify you of the new driver version. If this is not the case, the driver update information will not change, or Windows 10 will interrupt this process.
Windows 8/10 found that drivers do not need updating

If an older version of the driver was installed than the existing one, this is no longer an update, but a “rollback” of the driver. After restarting the PC, old problems with Wi-Fi communications that once existed may reappear.

But the device can also be removed by giving the appropriate command.

You can also remove the device from Windows before updating the driver

Windows 10 will ask you to confirm whether you want to remove Wi-Fi as a device. If there is a suitable driver in the system folder C:\Windows\, it can reinstall it automatically (or after restarting the PC).

If you want to remove the device, click the confirm button

If the auto-reinstallation of the Wi-Fi adapter does not occur, return to the Windows Device Manager, give the familiar driver update command and reinstall the Wi-Fi adapter according to the instructions above.

Video: Reinstalling the Wi-Fi driver in Windows 10

Checking router settings

So, nothing on the PC solved the problem. Try to access the Internet from another computer or gadget through the same router. For example, if an Android smartphone displays endless acquisition of an IP address, or displays the error “It is impossible to connect to the Internet via this network,” the problem lies in the router settings.

Physically, the router may fail - the router itself is not insured against any failure, be it a failure of the LAN/WAN interface or the Wi-Fi “distributor”. After many years of operation, natural wear and tear occurs. Or, when it was operated in conditions of dirt, heat and high humidity, it could fail prematurely even after several weeks or months of operation. If the LAN functional nodes on such a router fail, the Internet will disappear, and if the Wi-Fi radio subsystem breaks down, the PC or gadget will display the error “No connection” (“Wi-Fi networks not found”).

As an example - TP-Link routers.

Log in from any PC or gadget by typing the router's IP address into the address bar of your browser, for example, 192.168.1.1.
Enter the IP followed by the username and password for the router
Check (command “Network - WAN”) whether your WAN settings received from your provider are in place (if you use a cable provider, for example, home Internet from Beeline”), and whether the router connects to the Internet automatically.
Check if the protocol, name and password specified in the agreement are in place
If you do not have the “Static IP address” service activated (it is used mainly in work networks, for example, when you need to organize remote video surveillance of an office or industrial building), check whether the “Dynamic IP” option is enabled. Check to see if the Internet auto-shutdown feature is enabled when the Wi-Fi network is idle. If there are any discrepancies in the settings, correct them. Before connecting to the Internet, check all the necessary settings of the router - they will be inactive when the connection is working.
Give the command “Wireless network - Wireless mode settings”. Check that the Wi-Fi network is visible to all your devices, and that auto-selection of Wi-Fi speed, width and channel number occupied by the router on the air are enabled.
Check network name broadcast and auto-select Wi-Fi speed
Give the command “DHCP - DHCP Settings” and check the values of the starting and ending IP addresses. Without DHCP settings, each device would need to manually set IP addresses. If you do not assign IP addresses, the Wi-Fi network on your PC or gadget will be listed as unidentified (“perpetually receiving an IP”), and the Internet will not work.
Specify the range of IP addresses from which the router assigns specific ones to all clients
Give the command “Wireless Networks - MAC Address Filter” and make sure that device binding by MAC address is disabled.
TP-Link router does not use MAC address binding

If all the required settings are correct, return to the familiar WAN settings submenu and enable Internet access. Then connect to the router from any gadget or PC. Your favorite sites and apps should work.

Video: checking TP-Link wireless network settings

Disabling antivirus, firewall and firewall

Often, these three seemingly most important lines of protection from outside intrusions prevent you from freely accessing any sites. In a good way, security is important only when you use a PC purely for work, as a source of income, and carry out monetary transactions, or are an agent of some secret service, where the rules of work impose very strict restrictions on your security. In other cases, such protection is simply not needed.

Firewall and antivirus are everyone's choice. Which firewall you use - Agnitum Outpost or Windows 8 Firewall Control - is up to you. The same is true for antiviruses - suddenly you don’t like Kaspersky, but prefer, say, NOD32 or Avast.

Disabling Windows 10 Firewall in its settings

But the Windows firewall is the same for everyone. To disable it, do the following.

Launch the Windows 10 firewall using the command “Start - Control Panel - Windows Firewall”.
Go to Windows Firewall settings
Click the "Turn Windows Firewall on or off" link and turn off the firewall for private and public networks, first disabling pop-up notifications about security breaches for these networks.
Windows 8/10 Firewall no longer monitors Wi-Fi connections
Disable the same in the “Public/Private Profile” tabs - the additional firewall functions are the same here.

Close all windows by clicking OK, restart Windows 10. Now the Windows Firewall will not interfere with your Wi-Fi.

Disable Windows 10 Firewall service

To put an end to Windows Firewall interference once and for all, many people simply disable the Windows service of the same name.

Give the command “Start - Run”, enter and confirm the phrase “services.msc”.
The Windows Firewall service will no longer run

Restart Windows 10. If the service is disabled, the settings of the firewall itself will be unavailable.

Anyone can resolve the issue of suddenly failing Internet access via Wi-Fi. Almost a beginner can identify and eliminate purely software reasons. A breakdown of a router or gadget is detected in the first stages of testing. Have a good internet speed!

You can turn off Wi-Fi to save battery power on an airplane or other place where there is no Wi-Fi. With the Windows 10 Creators Update, you can now automatically turn on Wi-Fi by restarting your computer.

On the taskbar

This option is only available in the Windows 10 Settings app and the taskbar network menu. You won't see this option if you disable your Wi-Fi interface through the old Network Connections interface in Control Panel.

To turn off Wi-Fi from the taskbar, click the Wi-Fi icon in the notification area next to your clock and click the Wi-Fi button to turn it off.

If your Wi-Fi is set to Off, you can turn it on in 1 hour, 4 hours or 1 day - just like in the Settings app. The default option is “Manual” which means you need to click on the “Wi-Fi” icon in this menu to turn Wi-Fi back on.

Unfortunately, this option is not available when Airplane Mode is enabled. If you want to automatically turn on Wi-Fi, you need to turn off Wi-Fi rather than turn on Airplane Mode.

In the Settings menu

Go to Settings > Network & Internet > Wi-Fi. Set Wi-Fi connection to "Off" Here you can set automatic Wi-Fi connection after 1 hour, 4 hours or 1 day. The Manual option means that Windows will not automatically turn on Wi-Fi. You will have to do this yourself.