WiFi byfly settings. Network check and error correction

As a result, we get a Promsvyaz M200a modem that is completely ready for use. I repeat, the functionality of the modem allows you to use it as an ADSL modem, router, wireless Wi-Fi access point, to which you can connect several devices at once. For example: a computer via a network cable; laptop, phone, tablet via Wi-Fi at the same time.

In this way, you can quickly create a home local wireless network based on Promsvyaz M200a. Seamlessly access the Internet, share files and data between various devices without wires.

To set up the M200a modem, we need a working computer (laptop) without viruses and network cable(included with the modem) to connect to the modem for initial setup. Naturally - you must be a subscriber of the Beltelecom Internet provider with a connected and active service ByFly.
For normal operation of a computer or laptop, we recommend using effective antiviruses with an annual license and a description in Russian. You can compare and download antiviruses from developer sites using this link.

Initial setup of the ByFly Promsvyaz M200a ADSL modem:

We connect the computer’s network cable to the 1, 2 or 3rd LAN port of the modem (we use these ports for connection since the fourth is reserved for IP TV with DHCP disabled). Launch on your computer Chrome browser(Opera, FireFox, IE - any will do).
We go to the modem interface. To do this, enter the numbers (without spaces) into the address bar of the browser: 192.168.1.1 (this is the default IP address of the Promsvyaz M200a modem). Press Enter.
Sometimes the default IP address may be changed or unavailable. There is a fairly simple way.
If, for some reason, you cannot log in, you should check the state of the computer’s operating system and/or reboot the modem.
If you cannot get into the interface of the Promsvyaz M200a modem-router, try using a different browser. In some cases, it is better to reset the modem to factory settings and start the setup again. To do this, press and hold a special recessed button in the device body for 5 seconds with a sharp object (a needle, an unbent paper clip).
Sometimes it is enough to simply change the browser or remove the old antivirus (especially if it is not updated). An antivirus can cause problems on your computer, including working with WEB interfaces. In rare cases it is necessary. Especially if the Internet on your computer is slow with constant connection interruptions.
After the modem address has been entered, a window appears for entering the modem administrator name and password. Enter the password -admin, user -admin.
We get into the modem interface.
Click the Interface Setup tab. We go to the Interface Setup tab and the Internet subtab. Everything should be like in the picture below.
You need to change the fields: username (in the Beltelecom agreement - the user), password (in the agreement this is the password) and Bridge Interface. We check for the active Default Route checkbox in the “YES” position. Click SAVE.
Open the LAN tab. You don’t need to change anything here (DNS servers will rise automatically!)
Or as in the picture DNS ByFly for the city of Minsk.

For DNS settings set the DNS Relay menu to USED USER DESCOVERED DNS state DNS servers) - indicate yours.
Can be used public DNS Google servers - 8.8.8.8 and 8.8.4.4 - suitable for any region of Belarus. Read more about Google settings DNS in the article. Save the settings. If you use Promsvyaz M200a only as a wired ADSL modem - further customization not required.

Configuring the Promsvyaz M200a modem into wireless Wi-Fi router mode

The laptop should indicate that it is connected to the wireless network. If the laptop does not display the network, the driver for the network card may not be installed.

Sometimes there may be other problems with the laptop that lead to problems with wireless networks.
Use the services of our company: professional in Minsk.

Byfly is trademark Beltelecom company, which provides access to high-speed Internet. It so happens that users are not always able to correctly configure network access themselves. This applies to both home Wi-Fi connections and public ones. In this article we will consider both options.

Methods for connecting to public Wi-Fi

byfly wireless access points are installed in many public places, accessed through a user login and password. This data can be obtained temporarily, or you can secure it for a long time. Both methods are presented below.

Temporary free access

Convenient to use this option, if you urgently need to go online, but don’t want to make a map and enter into an agreement. Setup takes a couple of minutes.

Turn on Wi-fi on your device and connect to the network.
Go to your browser and try to access any website.
After the authorization page appears, enter your phone number and select the access time of “15 minutes.”
You will receive an SMS with your login and password.
Enter these details on the login page and click “Login”.
Ready! You can use the Internet for 15 minutes.

Pay attention! If you need more than 15 minutes, then indicate the required quantity and pay the selected tariff.

Permanent access

This tariff without subscription fee gives the right to top up the card and use Internet access at any time. You can get the card at service center Beltelecom, having concluded an agreement. This option is the most convenient for city residents.

Important! To receive a card, you must have identification documents.

Setting up a home modem

We've sorted out setting up a public network, and now let's start setting up Wi-Fi at home. All actions must be performed on a PC with a modem connected to it via cable. The setup is carried out using the example of the Promsvyaz M-200A device.

Go to your browser and enter "http://192.168.1.1"
In the window that appears, enter your login information. The default login and password is “admin” (If the login window does not appear, see the following instructions).
Click "Interface Setup" → "Internet".
Set the “ISP” parameter to “PPPoA/PPPoE”.
In the “Username” and “Password” fields, enter the user’s login and password (This data can be found in the contract for the provision of Internet connection services).
Set the “Bridge Interface” parameter to “Activated”, and below the “Default Route” parameter set it to “Yes”.
Click "Save".
In the top menu “Interface Setup” → “Wireless”.
Set the “PerSSID Switch” parameter to “Activated”.
Create a name and password for the Wi-Fi network.
Click "Save".

After completing these steps, you will have a Wi-Fi access point ready to use.

If you do not see the login window, configure the network card.

By right-clicking on the network icon, go to the “Network and Sharing Center”.
Go to “Change adapter settings”.
Right-click on the “Connect via local network» → “Properties”.
Select Internet Protocol Version 4 TCP/IPv4 → Properties.
Check the box next to “Use the following IP address.”
In the IP address line, enter “192.168.1.2”, enter the subnet mask “255.255.255.0”, and in the “Default gateway” enter “192.168.1.1”.
Enter the addresses of DNS servers (you can find them on the website

ByFly is a trademark of Beltelecom, which provides Internet access. The company offers its customers to configure the network using the service technical support. However, sometimes waiting in line can last for several hours.

You can establish access to the network yourself. Setting up WI-FI on ByFly takes only a few minutes. The main thing is to know how to do it. We hope that our article will help you set up network card and a router to access wireless internet.

PC setup

To establish Internet on a computer, first connect the router to the network and connect the devices with a wire. After this, the network card works.

The picture shows how to find out your OS on a computer:

Windows 7

To connect a Windows 7 PC to the network, proceed as follows:

enter the Start menu;
switch to the “Control Panel” sub-item;
“Network and Internet” - “Controller by networks” - this is the sequence of selecting the following items;
a new settings window appears, select the “Change adapter parameters” column;
the message appears: “Local network connection”, which is clicked with the mouse button located on the right side and redirected to the “Properties” sub-item;

click on the “Properties” button, which is located below the inscription;
put a tick in the box where it says: “Use the following IP address”;
enter the numbers into the column: 192.168.1.2, and if you plan to connect several devices to the router, then the coincidence of this data and the data from the last line is unacceptable;
Enter the following data into the “Main gateway” line: 192.168.1.1;

enter the addresses of DNS servers that are presented on the official BayFly portal.

Windows XP

For Windows XP, perform the following manipulations:

the first two points of action correspond to setting up a system with Windows 7;
after that, go to the “Network connections” sub-item;
the inscription appears: “Local network connection”, click on it with the mouse button located on the right side and select the “Properties” column;

under the inscription: “Components used by this connection”, select “TCP/IP connection protocol” and click on the “Properties” column;

enter digital values, as in the last four paragraphs Windows settings 7;
confirm the action and at the same time save the settings by pressing the “OK” key.

For a video tutorial on setting up a network card, watch the following video:

Setting up the router

You should also familiarize yourself with how to set up Wi-Fi on a modem. This depends on the brand of the device. However, there are a number of manipulations that are typical for all devices:

enter the router settings (to do this, enter the router address, which is indicated on the bottom panel - for example, for the Promsvyaz M-200A device it is 192.168.1.1);
open the settings site;
enter the login and password into the windows (factory default admin/admin);

Confirm your actions by pressing the “OK” button.

To set up Wi-Fi, follow the instructions that came with the router. We will look at setting up the Promsvyaz M-200A router for Wi-Fi connections on ByFly:

In the “Interface Setup” tab, select “Internet”.
In the “ISP” menu, select the third value “PPPoA/PPPoE”.
In the appropriate fields we enter the login and password that you received from the provider.
In the “Bridge Interface” line, select “Activated”.
In the “Default Route” line, mark “Yes”.

Click “Save” and select “Wireless” (at the top).
Activate “PerSSID Switch”.
We give our network a name and come up with a password.
Let's save.

Network connection

To connect to WI-FI using a wireless connection, perform the following manipulations:

the first four points correspond to actions for Windows 7;
After this, use the mouse button located on the right side to click on the inscription: “Wireless network connection" and are redirected to the "Properties" sub-item;
click on the inscription: “Internet Protocol 4 TCP/IPv4”;
click on the “Properties” button;
set the IP address and DNS addresses;
Using the mouse button located on the right side, click on the inscription: “ Wireless connection" and are redirected to the "Connection" sub-item;
The “Current connections” item opens, where you select the type of your connection;

click on the “Connect” button;
a security key is driven into the window;
Confirm your actions by clicking on the “OK” button.

If all manipulations are performed correctly, you can start using the Internet.

How to set up Wi-Fi on ByFly, you can also learn from the following video instructions:

Public Wi-Fi

You can connect to wireless Internet from Beltelecom even without concluding a contract, albeit for a short time. This can be done in public places.

Turn on Wi-Fi on your phone and select the Beltelecom network, click “Connect”.
Try to go into your browser and try to visit any site.
You will find yourself on a page for logging into the network, where you need to enter your phone number and select free Wi-Fi access.

Authorization information will be sent to your phone number. After entering them you will be able to use free access, though only for 15 minutes.

For permanent access to the Beltelecom public network, special reloadable cards are sold that give the right to use Internet access.

Personal account

IN Personal account You can pay for Internet services and view the status of your personal account. To enter your account you need to enter your username and password. Login is the contract number; the password must be specified in the contract. The password can be changed.

Information on router settings is available to Beltelecom clients in their Personal Account various models. This describes in detail how to configure a computer's network card on different operating systems and the procedure for connecting to Wi-Fi.

Hello friends! In this article I will give you the answer to the question - how to set up wifi on byfly? After all, using a router at home, you can access the Internet from several computers or devices that support wifi technology. Undoubtedly, this is very convenient and will save you from constantly getting in the way of Internet cables under your feet. In this article we will look at the ZTE modem and Promsvyaz M200A.

Setting up wifi on byfly begins by connecting the cable to your modem and computer. To do this, take the wire that came with the modem and connect one end to the computer’s network card, and the other to the LAN port on the modem. Just don’t confuse it with an ADSL port, it won’t fit there anyway.

Go to the modem interface

The basic setup of the byfly router begins with logging into the modem interface. To do this, open any Internet browser (Opera, GC, IE, MF, Safari) and in the address bar located at the very top, enter the following - 192.168.1.1 and press Enter. You will be prompted to enter your username and password. Enter the Username admin and Password admin. And you find yourself in the modem interface.

Setting up the Internet

And at the end, wifi setup on byfly I moved on to the main point - setting up an Internet connection. And so let’s get started, click the “Interface Setup” tab and immediately go to the “Internet” submenu. In the Encapsulation item, set the point to “PPPoA/PPPoE” and below select “PPPoE LLC”. Next, you need to enter your Internet connection information. In the “User Name” field, enter your name according to the contract. And in the “Password” field we also enter your Internet password. We put a dot in the “Bridge Interface” item on Activated. We check whether the point on the “Default Route” item is set to Yes. Click the “Save” button.

Setting up a local network

In principle, the local network settings can be left unchanged, or set as in the picture and enter the DNS of your city (the example shows for the city of Minsk). After changing the settings, do not forget to save by clicking on the “Save” button.

Setting up a wireless network

Setting up wifi on byfly moves on to the final point, namely setting up a wireless network. To do this, go to the Wireless tab. First, we activate wi-fi on the router (it may be disabled by default). In the “Access Point Settings” item, put a dot in the Activated option. In the “Pre-Shared Key” field, enter the password you created to enter the wi-fi network. We come up with and enter a network name in the “SSID” field (English layout is required. Click the “Save” button.

I hope that I was able to answer the question in more detail - how to set up wifi on byfly. I think that in this article I will help you become more experienced and raise your level of knowledge in the field of computer literacy and networking.

A hundred years ago, wireless communications for ordinary people was the ultimate fantasy, but progress does not stand still, and almost every home has Wi-Fi installed (which is short for Wireles Fidelity - wireless accuracy).

In order to switch from a direct connection to a wireless network, you need to purchase and configure a modem (router).

According to standard

Standard, or in other words, a version of the router protocol (which you can find in the instructions, on the box or on the Internet). Format wireless communication tells us about the power of Wi-Fi, Internet speed and network usage radius.

Modern standards:

802.11g - approved in 2003, maximum speed- 54 Mbps, power - up to 2.5 GHz
802.11n - approved in 2009, speed up to 300−600 megabits per second, power up to 5 GHz. As we can see, 802.11n is a newer and improved format, but the price of the router will be higher. When choosing, you should pay attention to how many meters of living space and how many devices will usually be connected to the network.

By number of antennas

The more external antennas, the more stable the signal will be. For example, for a small two-room apartment it is suitable router with one antenna, and for a three/four-room apartment they recommend at least two. You should also pay attention to the thickness of the walls. But there are routers that do not have external antennas, but only internal ones. In this case, you need to refer to the instructions again and look at the signal gain, it is expressed in dBi units. For example, 2−4 dBi is enough for a one/two-room apartment. On average, routers indicate 15 dBi.

How to connect wifi byfly

To configure the router, it is not necessary to call a specialist. This is a fairly simple task that anyone can handle. Let's take the byfly router as an example.

Connect the router to power.
On the router you can find connectors for the cable. They come in two types: WAN, where the main Internet cable is connected directly, LAN - a port connector for connecting a computer and a router directly. So, disconnect the main cable from the computer and attach it to the connector of the WAN router. Along with the router in the box you will find a medium-length cable. We connect one end to the computer, in the same place of the main cable, and the second - directly to the LAN connector. Make sure that the router signals light up!
Setting up the router happens through main computer. To do this, go to your browser and enter address bar the next one is 192.168.1.1. and navigate with Enter. Attention! Depending on the router model, the numbers may differ. If after the transition the browser gives an error with the network, or there is no response at all, then most likely the problem is in the network connection settings

Click start
Find and select the "control panel" tab
Depending on your Windows, find the adapter settings. If Windows 7, then through the network control center, if XP, then through “network connections”
By using right click mouse click on network connection/high-speed connection. Select properties and go to the “network” section. Let's look at the properties of the TCP/IP protocol. The “obtain an IP address automatically” and “obtain an address automatically” functions must be enabled.

We return to the browser and try again. An authorization window should appear, enter the word in both fields - Admin. Let's go to main panel Wi-Fi router settings - Promsvyaz. Select Interface Setup from the menu, then go to the Internet tab. The ATM VC field is left unchanged. In the Encapsulation field in the ISP parameters, select PPPoA/PPPoE. In the next, additional field PPPoA/PPPoE, you indicate the username and password, which you can find in the contract or find out by calling your network operator. Next, select Activated in the Bridge Interface parameters. And just below, select the YES item in the Default Route request. Next, save the data (Save button).
And here is the finish line. Remaining in the Interface Setup panel menu, select the Wireless section. As always, we leave the first field unchanged. For Wi-Fi to work and start distributing the network, select Activated in the PerSSID Switch request. Then the most pleasant and creative moment is to choose the name of the network (SSID) and come up with a password for it (Pre-Shared Key). Please note that it must have at least 8 Latin characters to be considered secure. All that remains is to indicate in the Authentication Type column - WPA-PSK. And in the Encryption section - TKIP.
We save the data, and your router should work! We check the availability of a wireless network through a phone or laptop and rejoice!

If during setup you mistakenly specified incorrect parameters, then click the Reset button, which is located on the router itself. After resetting all settings to factory default, try again. If you can't configure it manually, don't despair. Your Internet operator’s technical support specialist can always do this for you.