It is very difficult to imagine our life without the Internet; it is used every day and is the basis of our comfort. That is why a WiFi router (Dlink, Tplink, Zyxel, etc.) today is the main network equipment that is used in almost every home, apartment or office.
A Wi-Fi router makes it possible to turn a stable cable Internet connection into a convenient wireless communication, through which you can connect smartphones, tablets, TVs, laptops and any other devices. But before you get this wireless connection, you need the correct one (or 192.168.0.1, depending on the router manufacturer and device model). This is quite simple to do and this procedure will not take much of your time, but for a beginner everything seems complicated and confusing. Correct setting The router helps if and solve problems with Wi-Fi connection.
How to log into a Wi-Fi router to configure the addresses 192.168.1.1 and 192.168.0.1 (admin admin).
Your WiFi router has its own firmware inside it, it has its own interface through which you can perform various manipulations with the settings. But initially you need to go to your router, see all these settings, and only then start changing their parameters.
In order to log into the router for initial setup you need to use a cable connection (LAN, Ethernet). A laptop with an installed network adapter is suitable for these purposes. So, in WAN port On the back panel of your router you need to connect an Ethernet cable (network) from your provider (as a rule, this port has a different color, yellow and is offset from the others).
If you live in apartment building, such a cable is brought directly into the apartment when connecting to the Internet and interactive (iptv) television. Another one is sold along with the router network cable, which you need to insert into the LAN port of your computer and one of the LAN ports on the back of the router.
After connecting the router to the computer, you need to go to the router settings. Anyone can do this installed browser(Chrome, Yandex, Firefox, IE, etc.). Open the browser and enter http://192.168.0.1 in the address bar (you can do it without http).
You can see which address is in your router in the instructions, on the sticker on the bottom of the router, or just try entering both of these addresses in the browser. After you have entered the above address into the browser line and pressed Enter, you will be prompted to enter your username and password. If you see a window asking for a password, it means that all the previous steps were completed correctly, and you are already very close to your goal.
Everyone has WiFi routers The same login and password are used - admin/admin. You need to enter the value “admin” in the login line, and “admin” in the password line. After this, you will be taken to the router settings and can configure the Internet and settings Wi-Fi networks. The settings depend on the type of service provided by your provider.
Most of them provide automatic settings, so through a cable connection you should already have the Internet working right away. All you have to do is go to “Wireless Network Settings”, where you need to specify the desired name WiFi networks, security type and password. Now you can try connecting your laptop or smartphone to the wireless network. If it doesn't work, read on.
I can't log into the router using admin admin. 192.168.1.1 and 192.168.0.1 do not open.
You entered your username and password (admin admin), but were unable to log into the router, or were you denied access? This problem is quite common and you can solve it yourself.
Here are a few reasons why you may have difficulty logging into 192.168.1.1 or 192.168.0.1. Perhaps you have a used router (from a friend or acquaintances), which means that the previous owner could have set his own username and password to increase the level of security. Or you bought an exhibition copy in a store (from a display case), which was tested, repeatedly configured, and the standard password can also be changed.
It may also be that the router’s firmware has simply crashed and does not correctly accept the information you entered. Don't be afraid, the problem can be solved. But before proceeding with further actions, you need to make sure that you are entering your username and password on the English keyboard layout and Caps Lock is turned off.
The solution to this problem is very simple - you need to reset the router settings. To do this, you need to find the factory reset button on the back of your router. As a rule, it is small in size and recessed into the body, so it must be pressed with something thin (a paper clip, a pin, a toothpick). This is done so that you cannot accidentally press this button and reset all your previous settings.
Near the reset button, as a rule, the word “Reset” is indicated, but some manufacturers do not have this inscription. If you cannot find this button, then use the instructions for your router, in the section on resetting to factory settings, where its location will be indicated in detail.
In order to reset to factory settings and return the login and password to “admin/admin”, you need to disconnect all power cords, leaving only the power cable from the outlet. After this, you need to hold down the reset button for 10-15 seconds. You will see how all the indicators on the front panel of the router light up and go out, after which you can release the button, connect all the network cords and try to log into the router again (192.168.1.1, 192.168.0.1). The login and password will already be standard, as well as all the settings inside will be factory default.
As you can see, everything is very simple; you need to spend a few minutes to configure the router. Initially, you need to connect the router correctly, using the manufacturer’s recommendations, which are in the instructions. After that, go to the settings through the browser on your computer. Today, all manufacturers have a clear and simple interface for settings, so even a beginner can figure it out. If you have any questions, ask in the comments.
This article will tell you how to correctly enter 192.168.0.1 into the modem (router) settings.
To do this, enter 192.168.0.1 into the browser line and press enter.
If you are not logged in, you must first determine probable reasons problems. If the network router is configured for this address, then the computer must have an address distinguished by the last digit, that is 192.168.0.(2-254) . Otherwise, if the last digits match, a conflict will occur with the network equipment. How do you still go to 192.168.0.1?
Possible reasons for the lack of connection to the router via 192.168.0.1
First of all, you should know the settings network card. This can be done in several ways. Below will be discussed two essential for Windows 7/8-8.1:
The enabled state needs to be checked. To do this, right-click on the one where the connection was made, select “ State" and further - " Intelligence" In the window that opens, look at the address PC and router IP address.
As mentioned above, the computer's IP address must differ in the last digit from the gateway's IP address network equipment. Compound IPgateway installed automatically and preferred DNS — 192.168.0.1
, subnet mask — 255.255.255.0
, IP address 192.168.0.(2-254).
For example: 192.168.0.2.
If any numbers do not correspond to the required ones, they can be set manually. Click right click mouse to the network connection, then “ Properties» => « Internet Protocol Version 4", check the box " Use the following IP address» and set the required settings. 
192.168.0.1 login to your personal account
In most cases, popular manufacturers of routers and routers set the default login and password in the admin panel of your personal account admin admin. If you have changed your login information and forgotten it, you can reset the modem to factory settings by pressing the " Reset" Please keep in mind that other settings will also be reset, so you will need to clone Mas- address and set other details for connecting to the provider.
192.168.0.1 and 192.168.1.1 admin admin
Such common modems and Wi-Fi routers as: TP-Link, Zyxel, Qtech, Asus, NetGear, Huawei, ZTE, D-Link Often the input settings are set to both 192.168.0.1 and 192.168.1.1. You can read the instructions in another article at this link.
A router is a convenient solution for building a local and wireless network, allowing you to simultaneously access the Internet from several devices. However, to configure the router, you first need to install it correctly and go to the web interface, where the basic parameters of the equipment are indicated.
Connecting equipment
Before you go into the router settings, you need to install the equipment correctly. You will need:
- Router.
- Network cable.
- Network card on a computer.
Any user can handle installing a router - the main thing is to carefully inspect the ports and figure out what they are needed for. Explanatory inscriptions and different colors of connectors will help with this.
- The cable that the provider brought into the room is inserted into the WAN/Line/Internet port (usually it is blue).
- A network cable, which comes with the router, is installed in one of the LAN ports (mostly yellow). The second end of the patch cord is connected to network card computer.
- The power cable is installed in the appropriate connector.
Once all the wires are in place, press the power button. If everything is done correctly, several indicators on the router will light up: power, network connection and connection to the computer.
Setting up a router in the system
To open the router interface, you need to configure a network connection. Usually the necessary parameters are set automatically, but it would be a good idea to check that they are correct.
These are standard settings that allow the router to independently assign an address to the connected device (computer in this case) using a DHCP server.
Login to the interface
After connecting and configuring the equipment, you can proceed to resolving the issue of how to log into the router. On almost all routers, the interface address, login and password are indicated on a label located on the bottom of the device. 
If there is no sticker, then you can see the address for displaying the router web interface in the browser using software:
- Open Network and Sharing Center.
- Proceed to change adapter settings.
- Double click on the connection icon local network.
- Click Details and look at the Default Gateway value.
If you changed your login and password yourself, but cannot remember the new values, then use the Reset button on the router to reset its settings to factory settings. After resetting the settings, the identification data will become standard - admin/admin.
It is not necessary to look at the router address. Most manufacturers use the same address, so the procedure for launching the interface of different router models is not very different.
For example, TP-Link routers and D-Link use the IP address 192.168.0.1. After entering this value, an authorization window appears in the address bar of the browser; you need to enter your login and password in it. For some router models D-Link Dir You only need to specify your login; the password line can be left blank. 
U Asus routers and Netgear's default address is 192.168.1.1. The login and password are also usually standard – admin/admin. But there may be options: for example, for the NETGEAR WGR614 router the login will be “admin” and the password will be “password”.
For Huawei routers, the login information is slightly different from the usual values. The address to enter the interface is 192.168.100.1. The login and password are also not quite standard - root and admin, respectively. Some models have even more complex pairs for authorization. 
Routers Zyxel Keenetic have an easy to remember address my.keenetic.net. As an alternative, the standard address 192.168.1.1 is used. The login will be the word “admin”, and the password will be standard settings – 1234.
It seems like you can get confused, but in reality everything is simple. In 90% of cases the address will be 192.168.0.1. or 192.168.1.1, and the pair for authorization is admin/admin. If these values do not allow you to open the web interface, then read the instructions carefully - the address, login and password are always indicated there.
Possible login errors
If you go into the router settings using automatic settings If it doesn't work, try setting the login parameters manually using the router's IP address.
Knowing the router's IP address, you can manually specify the TCP/IPv4 protocol parameters:
To understand what values need to be specified, let’s take the router’s IP address - for example, 192.168.0.1. Based on this address, fill in the lines as follows:
- IP address – 192.168.0.2 ( last digit must be in the range from 2 to 254).
- Subnet mask – 255.255.255.0 (always remains the same).
- The main gateway is 192.168.0.1 (the router address is indicated here).
- The preferred DNS is 192.168.0.1 (the router address is also written down).
With these settings, the problem of launching the router's web interface through a browser should be resolved. Then all you have to do is set up the Internet and create wireless connection so that the Wi-Fi router begins to fulfill its functions of providing constant access to the network from different devices.
Hello!
I haven't written anything on my blog for almost two weeks. Not long ago I received a question from one of my readers. Its essence was simple: “Why can’t it log into the router 192.168.1.1?” I decided to answer not only him, but also to format the answer in the form of a short article.
How to open settings
In general, this address is used to enter settings on most routers and modems. There are actually quite a lot of reasons why the browser does not open them; let’s look at the main ones.
First, check the address to see if you copied it correctly: http://192.168.1.1/
Why can't I access 192.168.1.1?
Below are common problems
Incorrect browser settings
Most often, a problem with the browser occurs if you have turbo mode enabled (this is in Opera or Yandex Browser), or a similar function in other programs.
Also check your computer for viruses; sometimes, a web surfer may be infected with a virus (or an add-on, some bar), which will block access to some pages.
Router/modem is turned off
Very often, users try to go into settings, but the device itself is turned off. Be sure to check that the lights (LEDs) are flashing on the case and that the device is connected to the network and power.
After that, you can try resetting the router. To do this, find the reset button (usually on the back panel of the device, next to the power input) - and hold it down with a pen or pencil for 30-40 seconds. After this, turn on the device again - the settings will be returned to the factory settings, and you can easily access them.
Network card
A lot of problems happen due to the fact that the network card is not connected or does not work. To find out whether the network card is connected (and enabled) - you need to go to network settings: Control Panel\Network and Internet\Network Connections
For Windows 7, 8, you can use the following combination: press the Win+R buttons and enter the command ncpa.cpl (then press Enter).
Next, take a close look at the network connection your computer is connected to. For example, if you have a router and a laptop, then most likely the laptop will be connected via Wi-Fi (wireless connection). Right-click on it and click enable (if the wireless connection appears as a gray icon rather than in color).
By the way, you may not be able to enable the network connection because... Your system may be missing drivers. I recommend that if you have problems with the network, try to update them anyway. For information on how to do this, see this article: “ “.
Important! Be sure to check your network card settings. It is possible that your address is entered incorrectly. To do this, go to the command line (For Windows 7.8 - click on Win + R, and enter CMD command, then press the Enter key).
IN command line enter a simple command: ipconfig and press Enter.
After this you will see many options for your network adapters. Pay attention to the line “default gateway” - this is the address, it is possible that yours will not be 192.168.1.1.
Attention! Please note that the settings page in different models different! For example, to set the parameters of the TRENDnet router, you need to go to http://192.168.10.1, and ZyXEL - http://192.168.1.1/ (see the sign below).
Table: default logins and passwords
Antiviruses and firewalls
Very often, antiviruses and their built-in firewalls can block some Internet connections. In order not to guess, I recommend simply disabling them for a while: usually it’s enough to right-click on the antivirus icon in the tray (in the corner, next to the clock) and click on exit.
In addition, the Windows system has a built-in firewall that can also block access. It is recommended to turn it off for a while.
In Windows 7, 8, its settings are located at: Control Panel\System and Security\Windows Firewall.
Checking the hosts file
Quite often, users cannot access the settings of their own router. This problem becomes the reason why they cannot use the Internet. Considering the fact that the Internet is needed for work and everyday life, you need to solve the problem with the router as quickly as possible.
What are the most common reasons and what needs to be done to solve all the problems yourself? The answer to all these questions is in our article.
There are many reasons why users cannot access the settings of their router. Typically, you rarely need to go into the router settings, but this does not mean that the login problem can be ignored. That is why this problem needs to be solved as quickly as possible. So, what is most often the cause of any malfunction in the router?
The router is not plugged in or is turned on but there is no indication
Many users make a simple mistake and simply forget to plug in the router. As you know, a router cannot work without power supply. For this reason, before you try to go into the settings of the router, you need to make sure that it is plugged in.
It also happens that the router seems to be plugged in, but it still doesn’t turn on. The reason for this may be a malfunction of the outlet itself.
In some cases, the router is also turned on, but there is no indication. It is possible that everything is fine with the power supply, but the problem lies in the malfunction of the indicators themselves. They could simply burn out. This doesn't happen very often, but some models are notorious for constantly burning out indicators.
The computer is not connected to the router correctly
Some users do not know how exactly to connect the router to the computer. In case this is not about wi-fi connection, but about connecting the router to the computer via a wire, then for this you need to use the lan port. Unfortunately, quite often people confuse this port with other connectors that are located on the system unit. This is why numerous problems arise.
In order to solve this problem, you need to study the instructions for the router as carefully as possible. It shows exactly what the connector looks like into which you need to plug the wire from the router in order to connect it to the computer. Only after the user has read the instructions can the connection process begin.
In some cases, users even use the wrong cable. Usually the cable for connecting the router to the computer is thick enough, so it is easy to distinguish it from the rest.
Trying to access the wrong router address
In order to go into the router settings, you need to open any available Internet browser. You must enter the router address in the address bar of your browser.
Router addresses vary depending on the manufacturer and model. That is why in order to find out exact address, you need to study the instructions. If you still cannot find such information in the instructions, then you need to contact the developers of the router. To do this, you need to go to the equipment manufacturer’s website, and then visit the section where service contacts are indicated technical support. There I can tell you exactly what address you need to dial in order to enter the router settings.
If you have the router at hand, then you can look at its IP address on the back of the device.
Also with the help of almost any search engine You can find out the address for many router models. To do this, in the address bar of your browser you need to type the phrase “go to the XXX router settings”, where “XXX” is the router model.
If you still cannot enter the settings, you should enter the combination “192.1.1.0” or the combination “192.1.1.1”. This combination is suitable for many popular router models.
Another reason why users cannot enter the settings is due to simple ignorance of what address bar, in which you need to enter the modem address.
The browser's address bar is the white box that is located at the top of the browser. It displays the addresses of websites that the user visits. This is where you need to enter the modem address in order to configure it.
Router frozen
Quite often, users experience freezes. What should be done in this case? Most often, freezes are a consequence of overheating or problems related to the quality of the router components that are located directly in its case. What to do in this case?
First, try unplugging the router's power cord from the outlet and plugging it back in. After this, the router will start again and perhaps the problem will no longer appear.
In order to prevent problems associated with overheating, you need to place the router away from system unit. It is possible that the heat that comes from it is the cause of overheating. It is also worth understanding that the router may overheat if it is placed near a window and is exposed to direct sunlight.
If overheating is associated with a technical defect, then repairing the router will be much more difficult. To do this, you need to replace certain elements directly in the router case itself. You also need to understand that this can only be done if you can get spare parts. The easiest way is to replace such a router from the manufacturer if the warranty has not yet expired.
The computer does not receive an IP address from the router
Sometimes the router cannot establish a connection with the computer. The reason for this may be that the user has not enabled DHCP.
In this case, you need to go to your computer’s network settings and find an option called DHCP, and then check the box next to it.
On every version operating system In Windows, you need to go to different menus to do this, but finding them will be easy.
All you need to know is that all settings related to DHCP are in the section network connections and the Internet.
Incorrect login or password
Another common problem involves entering an incorrect or outdated password. Typically, the default username and password on many routers is “admin”. If it is not suitable, you need to clarify the information from the instructions.
Another popular problem concerns incorrectly entering a login or password after the user has already installed New Password instead of the factory one. What to do in such a situation? To do this, you need to find the reset button on the router case and press it. After this, all settings of the router will be reset.
It is worth understanding that in this case you will have to configure the modem again, but this is the only way to reset the password if the user has forgotten it.
It happens that to press the reset button you need to use a needle, since this button is recessed deep into the case just so that users do not press it accidentally.
